It is better to use a long password, for example four or more random unrelated words with a number or special character inserted somewhere, than to use a short or commonly used password or a password that a computer could guess. You then login using SSH as soon as possible (within seven days) to set a new, unique and good password.Īlways use a unique password for each login account! When that has been done, the account ready for use within 10 minutes and you can then login using your chosen password.įor other clusters (e.g Cirrus and Stratus), you get an email with your username and preliminary password. When that has been done, the account ready for use within 10 minutes and you can then login using your chosen password.įor Bi and Nebula, you will get a URL that you use to choose the password (within seven days). When the account is ready to be created, you will receive an email to your registered email address (shown in your SUPR contact information) with information on how to proceed.įor Tetralith, Sigma, and Berzelius, you will get a URL that you use to choose the password (within seven days) and enable two-factor authentication ("2FA"). Just use the "Request Account on Clustername" button and confirm it on the next page.Ĭhecking your request and approving your account requires some manual work, so you might have to wait for some time (up to a working day) before the next step. Under the "Possible Resource Account Requests" headings you find the NSC resources you can apply for login accounts on. You will see the login accounts you already have at NSC and other centres. Login to SUPR and go to the Accounts page. Note: You can request login accounts before the User Agreement and the project memberships have been approved, but the requests are not handled until they are approved. You need to request the login account, as we do not automatically create login accounts before we know that you are going to use it. The project needs to have time allocated (now or in the future) on the resource you want a login account for. See the information about becoming a member of a project if you have not already taken care of that. Note: if you have accepted the NSC-specific User Agreement earlier (when getting another login account before this was moved to SUPR) and you cannot easily get the NAISS User Agreement handled, please email us at support at nsc dot liu dot se. You will get an email from SUPR when it has been approved. If you have accepted the SNIC User Agreement before, you will be able to accept the NAISS User Agreement online in SUPR (even if you did the SNIC User Agreement via the paper alternative).ĭepending on how you take care of the NAISS User Agreement, it may be approved automatically or it may require manual checking (for example if you choose to use the paper alternative). You can check the status on the SUPR Personal Information page. If you have already accepted the NAISS User Agreement, you will not see the "Handle User Agreement" button. To take care of this, login to SUPR and use the "Handle User Agreement" button on the top of the page. Once is enough you do not have to do this again if you want further NSC accounts or accounts at other centres. You need to have accepted the NAISS User Agreement. To get a login account on a resource, you need to:Įach step is described in more detail below. The rest of this page does not apply in that situation. For example, you do not have a login account on Tetralith just because you have one on Sigma.įor login accounts on dedicated SMHI resources such as Bi, please refer to SMHI access. Please note that login accounts are created separately for each NSC resource. Since its inception in 2003, Care Everywhere has been focusing on the development of medical device data system software (MDDS) integrating point of care medical devices with hospital information systems.Ĭare Everywhere’s Network Operation Center (NOC) monitors all connected medical devices and installed Gateway server instances to help hospital clients manage their smart infusion pump fleet and support an integrated nursing medication administration workflow.To login to an NSC resource, you need a login account. The company’s Infusion Pump Gateway Server software is an FDA registered Class 1 medical device.Ĭare Everywhere’s Infusion Pump Gateway software product has been deployed to more than 500 healthcare provider organizations, connecting more than 200,000 diagnostics and therapeutic devices at the point-of-care. Care Everywhere is an ISO 13485:2016 certified software medical device company focused on integrating point-of-care medical devices such as infusion pumps and vital sign monitors with hospital information systems to improve patient safety, nursing productivity, and documentation.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |